Changelog

7.0.7.0

Fixed problems while regenerating relations. The content from 'param_relations.txt' was processed line by line. This caused problems e.g. with 'IF' commands.[RM-12443]
A gap was created between the fastener and the placement surface while placing a fastener on very thin models. [SPR-13085083][RM-12051]

Reading of *.hol files in IFX reworked. Ignore *.hol files if 'THREAD_SERIES' and 'THREAD_NAME' is already in list. [RM-11337]
Add corruption check for IFX fastener groups. Output found errors to the message log. [SPR-10503770][RM-11148]
Option 'GEN_DIGITS' removed. The value was not used. [SPR-12778104][RM-11846]
Ignore tabs at the end of SUBINFO. [11334]
Rework functionality if 'HOLE_VISIBILITY' is set to 'NO'.
Do not show hole 'Hole Visibility' layout in 'Additional Options' dialog, disable all hole-icons to visualise that holes will not be created, do not paint holes in previews and do not check if hole charts are valid. [SPR-13074974][SPR Task-13074975][RM-11939][RM-11942]

Add Additional Tools information offered by B&W Software GmbH [RM-11322][RM-11323]
Support body colors for 2D-preview. [RM-11236][RM-11237]

Support unicode characters in param_relation.txt. [RM-10778][SPR 11357093][SPR Task-11357094]

Disallow thread-surfaces as a position reference. [RM-10976][SPR-11285257][SPR Task-11285260]

Fix problem with new designated parameters from 'ifx_start_mdl.cfg'. If the parameter is also used in a 'param_relation.txt' then the designation status gets lost. [RM-11007]
Fix problems while RUN_MAPKEY* options. [RM-7208]
Fix for COLOR_HOLES option. The COLOR_STDPARTS value was used for COLOR_HOLES too. [RM-10986]
Adding a fastener with option assemble fastener on all instances (from a pattern) generates a premature exit. This problem is fixed now. The error could occurs if a cylindrical surface from inside a extrude was selected. IFX only supports cylindrical surfaces from holes. If the extrude contains planar surfaces, this could lead to the problem. [RM-10956][SPR-12035414][SPR Task-12035417]

Hole file selection. Allow selection of hole file if more than one is available. [RM-5255]
Add new screw options for clearance hole to control the diameter. [RM-5255]
CLEARANCE_HOLE_USE_LIMITS - Set limits for min. and max. clearance hole diameter.
CLEARANCE_HOLE_DIAMETER_OVERRIDE - Allow specifying the clearance hole value instead of the standard value.

Version for Creo Parametric 7.0.3.0.
Support of special character for THREAD_NAME or THREAD_SERIES in creo hole chats. [RM-10498][SPR-11163572][SPR Task-11163573]

The automatic length of the screws was not correct for prevailing torque type hexagon nuts. For NUTTYPE 50 and NUTTYPE 60 the L1 value is now used for autolength calculation. [RM-10462][SPR-11169725][SPR Task-11169728]

Add new Option PATTERN_OPTION to control the pattern behavior for fasteners. [RM-9490][RM-9581]

Improve the creation time of new fasteners [RM-10070][RM-10072]
Show error image if a part cannot be modified. In this case no holes are created by default. The user can change this in the 'Additional Options' dialog. [RM-9390][RM-9584]
The creo option 'drilled_hole_tip_angle' can be used to control the tip angle of drilled holes now. The default value is 118° if the option is not set. [RM-8281]

Fix problem. IFX run into a problem in 'Additional Options' dialog. While searching for locked part a value was assigned to an invalid pointer.