Changelog

7.0.9.1

Bugfixes

• Fixed an error when reading *.dat files with #FAMTAB. [RM-14111]

7.0.9.0

Bugfixes

• Fixed problem with hole tables while creating and redefining a dowel pin. [RM-13560][SPR-13773021]
• Remove blanks at the end of an instance name. [RM-13661]
• Fixed reading of hole charts regarding 12 or 18 columns. [RM-13521][SPR-13804155]
• Fixed problem with the determination of the minimum and maximum diameter of the countersink. [RM-13612]
• The values from 'ifx_start_mdl.cfg' are assigned before creating new parameters from the *.dat file. Otherwise the designated status will be lost. [RM-13502]
• Fixed problem with placement of nut or insert in subassembly. [RM-13379]
• Fixed an error when reading *.dat files. If a line contained more than 256 characters, a crash occurred. [RM-13454]

7.0.8.0

Bugfixes

• Problem with redefinition of countersunk screws fixed. The problem occurred in combination with Auto-UDF. The Auto-UDF information was lost. [RM-12568]
• Fixed Creo crash when Redefine a screw fastener. [RM-12934][SPR-13483120]
• Fixed a problem in the screw dialog file. If the 'STRING' contains a space, the file is corrupted. [RM-12551]
• Fix diameter error in 'Unhardened_Ground.dat'. Change wrong diameters to '0.6250'. [RM-12486]

7.0.7.0

Improvements

• Version for Creo Parametric 7.0.7.0.

7.0.6.1

Bugfixes

• Fixed problems while regenerating relations. The content from 'param_relations.txt' was processed line by line. This caused problems e.g. with 'IF' commands.[RM-12443]
• A gap was created between the fastener and the placement surface while placing a fastener on very thin models. [SPR-13085083][RM-12051]

7.0.6.0

Bugfixes

• Reading of *.hol files in IFX reworked. Ignore *.hol files if 'THREAD_SERIES' and 'THREAD_NAME' is already in list. [RM-11337]
• Add corruption check for IFX fastener groups. Output found errors to the message log. [SPR-10503770][RM-11148]
• Option 'GEN_DIGITS' removed. The value was not used. [SPR-12778104][RM-11846]
• Ignore tabs at the end of SUBINFO. [11334]
• Rework functionality if 'HOLE_VISIBILITY' is set to 'NO'.
  Do not show hole 'Hole Visibility' layout in 'Additional Options' dialog, disable all hole-icons to visualise that holes will not be created, do not paint holes in previews and do not check if hole charts are valid. [SPR-13074974][SPR Task-13074975][RM-11939][RM-11942]

7.0.5.0

Improvements

• Add Additional Tools information offered by B&W Software GmbH [RM-11322][RM-11323]
• Support body colors for 2D-preview. [RM-11236][RM-11237]

Bugfixes

• Fix problems in hole chart layout. [RM-11176][RM-11177][RM-11121][RM-11287]
• Fix problem with offset '-0.1' for screw-in connections. [RM-11174]

7.0.4.0

Enhancements

• Support unicode characters in param_relation.txt. [RM-10778][SPR 11357093][SPR Task-11357094]

Improvements

• Disallow thread-surfaces as a position reference. [RM-10976][SPR-11285257][SPR Task-11285260]

Bugfixes

• Fix problem with new designated parameters from 'ifx_start_mdl.cfg'. If the parameter is also used in a 'param_relation.txt' then the designation status gets lost. [RM-11007]
• Fix problems while RUN_MAPKEY* options. [RM-7208]
• Fix for COLOR_HOLES option. The COLOR_STDPARTS value was used for COLOR_HOLES too. [RM-10986]
• Adding a fastener with option assemble fastener on all instances (from a pattern) generates a premature exit. This problem is fixed now. The error could occurs if a cylindrical surface from inside a extrude was selected. IFX only supports cylindrical surfaces from holes. If the extrude contains planar surfaces, this could lead to the problem. [RM-10956][SPR-12035414][SPR Task-12035417]

7.0.3.0

Enhancements

• Hole file selection. Allow selection of hole file if more than one is available. [RM-5255]
• Add new screw options for clearance hole to control the diameter. [RM-5255]
  CLEARANCE_HOLE_USE_LIMITS - Set limits for min. and max. clearance hole diameter.
  CLEARANCE_HOLE_DIAMETER_OVERRIDE - Allow specifying the clearance hole value instead of the standard value.

Improvements

• Version for Creo Parametric 7.0.3.0.
• Support of special character for THREAD_NAME or THREAD_SERIES in creo hole chats. [RM-10498][SPR-11163572][SPR Task-11163573]

Bugfixes

• The automatic length of the screws was not correct for prevailing torque type hexagon nuts. For NUTTYPE 50 and NUTTYPE 60 the L1 value is now used for autolength calculation. [RM-10462][SPR-11169725][SPR Task-11169728]

7.0.2.0

Enhancements

• Add new Option PATTERN_OPTION to control the pattern behavior for fasteners. [RM-9490][RM-9581]

Improvements

• Improve the creation time of new fasteners [RM-10070][RM-10072]
• Show error image if a part cannot be modified. In this case no holes are created by default. The user can change this in the 'Additional Options' dialog. [RM-9390][RM-9584]
• The creo option 'drilled_hole_tip_angle' can be used to control the tip angle of drilled holes now. The default value is 118° if the option is not set. [RM-8281]

Bugfixes

• Fix problem. IFX run into a problem in 'Additional Options' dialog. While searching for locked part a value was assigned to an invalid pointer.

7.0.1.0

Improvements

• Add What's New Dialog. [RM-9669]

Bugfixes

• Problems with 'SUBINFO' for family table dowel pins fixed. [RM-9644]
• Fix the 31 character limit for file name. [RM-9677][SPR-10054607]
• Fix problem if name for reference is longer than 80 signs. [RM-9920]

7.0.0.0

Enhancements

• Creo 7.0 ready version.
• Multibody support.
• Minitoolbar support.
• Enhance usage of ifx_screw_data.cfg and ifx_pin_data.cfg files.
• Enhance definition of placement references in Fastener Data Files.
• Enhance usage of relations.