Changelog

9.0.1.1

Bugfixes

• Fixed an error when reading *.dat files with #FAMTAB. [RM-14111]

9.0.1.0

Enhancements

• If a translation file is missing, the name of the file is output in the trail file. [RM-13184][SPR-13567673]

Improvements

• Set thread depth to 'Through Thread' if a hole with through thread is selected. [RM-12460][SPR-13264653]

Bugfixes

• Fixed problem with hole tables while creating and redefining a dowel pin. [RM-13560][SPR-13773021]
• Fixed problem with the determination of the minimum and maximum diameter of the countersink. [RM-13612][C16322899]
• The values from 'ifx_start_mdl.cfg' are assigned before creating new parameters from the *.dat file. Otherwise the designated status will be lost. [RM-13502]
• Fixed problem with placement of nut or insert in subassembly. [RM-13379]
• Fixed an error when reading *.dat files. If a line contained more than 256 characters, a crash occurred. [RM-13454]
• Problem with redefinition of countersunk screws fixed. The problem occurred in combination with Auto-UDF. The Auto-UDF information was lost. [RM-12568]
• Fixed Creo crash when Redefine a screw fastener. [RM-12934][SPR-13483120]

9.0.0.0

Enhancements

• Creo 9.0 ready version.
• Support unicode characters in param_relation.txt. [RM-10778][SPR 11357093][SPR Task-11357095]

Improvements

• Disallow thread-surfaces as a position reference. [RM-10977][SPR-11285257][SPR Task-11285261]

Bugfixes

• Fixed a problem in the screw dialog file. If the 'STRING' contains a space, the file is corrupted. [RM-12551]
• Fix diameter error in 'Unhardened_Ground.dat'. Change wrong diameters to '0.6250'. [RM-12486]
• Fix error "No hole charts found for this hole types" when placing dowel pin Fastener using IFX with a drill diameter out of standard hole table and this hole cannot be created. New 'dowelpin*.hol' files with all dowel pin diameters have been added. [SPR-8702705][RM-10358]
• Fixed problems while regenerating relations. The content from 'param_relations.txt' was processed line by line. This caused problems e.g. with 'IF' commands.[RM-12443]
• A gap was created between the fastener and the placement surface while placing a fastener on very thin models. [SPR-13085083][RM-12051]
• Add corruption check for IFX fastener groups. Output found errors to the message log. [SPR-10503770][RM-11148]
• Option 'GEN_DIGITS' removed. The value was not used. [SPR-12778104][RM-11846]
• Rework functionality if 'HOLE_VISIBILITY' is set to 'NO'.
  Do not show hole 'Hole Visibility' layout in 'Additional Options' dialog, disable all hole-icons to visualise that holes will not be created, do not paint holes in previews and do not check if hole charts are valid. [SPR-13074974][SPR Task-13074977][RM-11939][RM-11944]
• Adding a fastener with option assemble fastener on all instances (from a pattern) generates a premature exit. This problem is fixed now. The error could occurs if a cylindrical surface from inside a extrude was selected. IFX only supports cylindrical surfaces from holes. If the extrude contains planar surfaces, this could lead to the problem. [RM-10958][SPR-12035414][SPR Task-12035418]
• THREAD_NAME in hole chart with unicode text is recording as `????' to trail file. [RM-10713][SPR-11246433][SPR Task-11246434]