IFX Changelog
9.0.5.1
Bugfixes
- Add and update translation strings. [RM-16150]
9.0.5.0
Enhancements
- Add new screw option COUNTERSINK_HOLE_USE_LIMITS. [RM-15262][SPR-14504539]
- Use API 'ProElementHole*Set()' to set the thread series and the screw size by value. If the value (i.e. M10x1.5) does not exist, an exception is thrown. In the past the thread series and the screw size where set by index. If the index was wrong, creo crashes immediately. [RM-15348]
- Ignore values (e.g. tabs and spaces) behind 'THREAD_DATA' in hole charts. [RM-15215]
- Before retrieving, check if a fastener exists to avoid the message: 'fastener-mdl' cannot be retrieved.
If the fastener model does not yet exist, create it using the template. [RM-14618]
Bugfixes
- Only accept cylindrical surfaces as multi-reference. [RM-15199]
- Consider hole charts in working directory. [RM-14899][SPR-14386755]
- Solved problem for screw-in fasteners. Offset (depth) was set to '-0.1'. [RM-14871]
9.0.4.0
Bugfixes
- Parameter values for the 'BUW__ID' fastener component parameters were set to '0' during redefinition. [RM-11509]
9.0.3.0
Bugfixes
- Fixed an error when reading *.dat files. If there was a space in the first column, there were problems when placing fasteners. [RM-14361][SPR-14131006][SPR-14130745][C-16573455]
- An issue related to the placement of fasteners on assembly cut surfaces has been fixed. [RM-14373][RM-14406][SPR-14146142][C-16584416]
- Fixed a problem related to redefining fasteners in subassemblies. [RM-13590]
- For inserts, the pitch 'P' was used instead of 'P1' to determine the hole thread series. [RM-14292]
- The creation of holes was improved.
If an edge was hit on the exit surface, the hole was not created. [RM-13792][SPR-13818141][C-16381450]
9.0.2.0
Bugfixes
- Fixed an error when reading *.dat files with #FAMTAB. [RM-14111]
- The problem with redefining a screw with an insert has been fixed. The 'BASIC_DIAM' and 'THREAD' diameters of the screw instead of the insert were used to get the hole diagram.
- Problem with resetting the hole note fixed. The 'RUN_MAPKEY_*' options have been removed. New API is used to reset the note. [RM-5837][SPR-13760849]
- Fixed problem with *.dat file having lines with the empty tabs. In this case the size was shown as 0 (zero). [RM-13744][SPR-13807791]
- Fixed reading of hole charts regarding 12 or 18 columns. [RM-13521][SPR-13804155]
- Remove blanks at the end of an instance name. [RM-13661]
9.0.1.0
Enhancements
- If a translation file is missing, the name of the file is output in the trail file. [RM-13184][SPR-13567673]
Improvements
- Set thread depth to 'Through Thread' if a hole with through thread is selected. [RM-12460][SPR-13264653]
Bugfixes
- Fixed problem with hole tables while creating and redefining a dowel pin. [RM-13560][SPR-13773021]
- Fixed problem with the determination of the minimum and maximum diameter of the countersink. [RM-13612][C16322899]
- The values from 'ifx_start_mdl.cfg' are assigned before creating new parameters from the *.dat file. Otherwise the designated status will be lost. [RM-13502]
- Fixed problem with placement of nut or insert in subassembly. [RM-13379]
- Fixed an error when reading *.dat files. If a line contained more than 256 characters, a crash occurred. [RM-13454]
- Problem with redefinition of countersunk screws fixed. The problem occurred in combination with Auto-UDF. The Auto-UDF information was lost. [RM-12568]
- Fixed Creo crash when Redefine a screw fastener. [RM-12934][SPR-13483120]
9.0.0.0
Enhancements
- Creo 9.0 ready version.
- Support unicode characters in param_relation.txt. [RM-10778][SPR 11357093][SPR Task-11357095]
Improvements
- Disallow thread-surfaces as a position reference. [RM-10977][SPR-11285257][SPR Task-11285261]
Bugfixes
- Fixed a problem in the screw dialog file. If the 'STRING' contains a space, the file is corrupted. [RM-12551]
- Fix diameter error in 'Unhardened_Ground.dat'. Change wrong diameters to '0.6250'. [RM-12486]
- Fix error "No hole charts found for this hole types" when placing dowel pin Fastener using IFX with a drill diameter out of standard hole table and this hole cannot be created. New 'dowelpin*.hol' files with all dowel pin diameters have been added. [SPR-8702705][RM-10358]
- Fixed problems while regenerating relations. The content from 'param_relations.txt' was processed line by line. This caused problems e.g. with 'IF' commands.[RM-12443]
- A gap was created between the fastener and the placement surface while placing a fastener on very thin models. [SPR-13085083][RM-12051]
- Add corruption check for IFX fastener groups. Output found errors to the message log. [SPR-10503770][RM-11148]
- Option 'GEN_DIGITS' removed. The value was not used. [SPR-12778104][RM-11846]
- Rework functionality if 'HOLE_VISIBILITY' is set to 'NO'.
Do not show hole 'Hole Visibility' layout in 'Additional Options' dialog, disable all hole-icons to visualise that holes will not be created, do not paint holes in previews and do not check if hole charts are valid. [SPR-13074974][SPR Task-13074977][RM-11939][RM-11944]
- Adding a fastener with option assemble fastener on all instances (from a pattern) generates a premature exit. This problem is fixed now. The error could occurs if a cylindrical surface from inside a extrude was selected. IFX only supports cylindrical surfaces from holes. If the extrude contains planar surfaces, this could lead to the problem. [RM-10958][SPR-12035414][SPR Task-12035418]
- THREAD_NAME in hole chart with unicode text is recording as `????' to trail file. [RM-10713][SPR-11246433][SPR Task-11246434]